主要荣誉：
1、河南省杰出青年基金（河南省科技厅，2007）
2、河南省教育厅学术技术带头人（河南省教育厅，2007年）
3、河南省中青年骨干教师（河南省教育厅、人事厅，2000年）
近5年内成果清单：
1、发表论著、论文
李海梅，《注塑成型及模具设计实用技术》，第二版，北京：化学工业出版社，2008.12
张晓黎，李海梅等，《塑料加工和模具专业英语》（英汉对照版），北京：化学工业出版社，2007..11
Shen CY, Li HM, Chen SC. Numerical simulation of deformations for injection molded parts，SPE ANTEC, 2005, May 1-6, Boston, Massachusetts,61:583-587
Chen SC, Li HM, Shen CY. 3D Simulation and Verification for Mold Temperature Control Technoloies,SPE ANTEC, 2005,May 1-6, Boston, Massachusetts, 61:491-495
Li HM, Shen CY, Shi L. Preform node optimization for injection molding warpage analysis,?SPE ANTEC, 2005, May 1-6, Boston, Massachusetts, 61: 647-651
Li HM, Shen CY, Chen SC. Photoelastic measurement and numerical simulation of residual stresses, SPE ANTEC, 2006, May 7-11, Charlotte, NC, 62: 1235 -1240
Li HM, Shen CY, Chen SC, Zhang XL. Prediction of the weld-line-induced strength reduction for nylon6 and its nanocomposites, ANTEC 2007，May 6-10, Cincinnati, Ohio, 63: 577-580
Li HM, Shen CY, Jiang Yan, Wang X, Cao W. Numercial simulations of residual stresses in polycarbonate injection mold parts, ANTEC 2007,May 6-10,Cincinnati, Ohio, 63: 610-614
Li HM, Jiang K, Xu WL, Shen CY. Effects of processing parameters on optical properties of injection molded polystyrene parts, ANTEC 2007, May 6-10, Cincinnati, Ohio, 63: 590-594
Chen SC, Li HM, Wang YC. Temperature effects on micro-channel replication of ?hot embossing and injection molding process，ANTEC 2008, May 4-8, Milwaukee, WI, 64:489-493
Li HM, Shen CY, Chen SC. Heating/cooling technologies for injection molding to improve products quality, ANTEC 2008, May 4-8, Milwaukee, WI, 64:494-498
Li HM, Peng YY, Turng LS etal .Research on residual stresses of injection molded PC parts, ANTEC 2009 , June 22-24, Chicago, Illinois USA, 1689-1693
Peng YY, Li HM, Turng LS. Rheo-dielectric method for shear stress measurement during injection molding process，Polymer Enigneering and Science，50（1）：66-76，2010
Martinez K, Li HM，Turng LS，Kramschuster S，Lee JJ. Effects of Nucleating and Clarifying Agents on the Morphology and Mechanical Properties of Microcellular Injection Molded Polypropylene Parts, International Journal of Polymer Technologies, 1 (1) : 57-66, 2009
Li HM, Chen SC, Shen CY, Chau SW, Lin YW. Numerical simulations and verifications of cyclic and transient temperature variations in injection molding Process, Polymer-Plastics Technology and Engineering, 48: 1-9, 2009
Li HM, Shen CY, Chen SC, Wang HX, Wang X. Improvement of product quality of injueciton molded parts by modified heating and cooling technologies. GAK Gummi Fasern Kunststoffe - Fachmagazin für die Polymerindustrie, 62 (5):280-284, 2009
Chen SC, Li HM, Su PL, Hu CS. Investigation of the weldline strength of injection molded nylon 6 nanocomposite, Journal of reinforced plastics and composites, 28(18): 2197-2210, 2009
Chen SC, Li HM, Hwang SS, Wang HS. Passive mold temperature control by a hybrid filming-microcellular injection molding processing, International Communications in Heat and Mass Transfer, 35(7): 822-827, 2008
Lin YW, Li HM, Chen SC, Shen CY. 3D numerical simulation of transient temperature field for lens mold embedded with heaters. International Communications in Heat and Mass Transfer, 32(9), 1221-1230, 2005
2、软件版权
国家软件版权登记：注射模报价软件MoldQuoterV1.0，软著登字[065079]号，登记号：2006SR17413, 2006年 （第1）
国家软件版权登记：基于材料边界的温度场模拟软件MoldcoolSYS V1.0，软著登字[073223]号，登记号：2007SR07228，2007年 （第1）
国家软件版权登记：塑料制品光弹应力条纹识别软件StressNumViewV3.0，软著登字[081256]号，登记号：2007SR0715261，2007年 （第1）